P10 LED Module
Addressable Lighting series 1024 (32 x 32) LED Matrix Red, Green, Blue (RGB) 128.00mm L x 128.00mm W
Category: PIXEL LED
Huidu HD-F1 Controller Card
HD-WF1（abbr WF1）equipped with 1HUB75E Port. It is a full color series of control card. It supports Wi-Fi and U disk to update programs. It is suitable for door lintel led screens, store signboard screens, Vehicle-mounted screen and other occasions. Application software: HD2020 and LedArt (APP).The software interface is simple, the operation is convenient, and the rich display mode has the characteristics of low cost and high cost performance, and supports various full-color led modules.
Huidu HD-W00 Controller Card
Huidu Wifi Card for Single and Double Color LED Sign control Size: 320*32 Dots Output: 2*HUB12 Memory: 2M byte Control type： WIFI
WS2811 LED Pixel Strip Light 5050 RGB 30
WS2811 60 LEDs/m RGB Addressable LED Pixel Strip Light 12V DC ProgrammableThe WS2811 is a three-output channel LED driver circuit. Internally, it has a signal reshaping amplification driving circuit and an intelligent digital port data latch. A precise internal oscillator is also included, as well as a 12V voltage configurable constant current output drive. For the purpose of reducing power supply ripple, the 3 output channels are designed to delay turn-on function. A single NZR communication mode is used by the IC. Following the chip's power-on reset, the DIN port receives data from the controller, the first IC collects the initial 24bit data and sends it to the internal data latch, while the other data is reshaped by the internal signal reshaping amplification circuit and sent to the next cascade IC via the DO port. The signal is reduced by 24 bits after transmission for each chip. The chip cascade number is not limited by signal transmission because of auto reshaping transmit technology; it only depends on the signal transmission speed. The data latch of the IC produces various duty ratio signals at the OUTR, OUTG, and OUTB ports depending on the received 24bit data. When the DIN port inputs a reset signal, all chips synchronously send the incoming data to each segment. It will be updated with fresh information. Following the completion of the reset signal. The control signals of the OUTR, OUTG and OUTB ports were unaltered before a fresh reset signal was received. After receiving a low voltage reset signal, the IC supplied PWM data to the OUTR, OUTG, and OUTB ports, and the time retained was above 50us.
WS2812B LED Pixel Strip Light 5050 RGB 30
This is the waterproof version of addressable RGB LED strips based on the new WS2812B LEDs which have built-in LED drivers and addressing Each LED on this strip is individually addressable, which means that you can set a different colour for each of the 30 LEDs in a 1 meter strip. All you need is one pin on your microcontroller/Arduino/Teensy etc. to control an entire strip of LEDs. These strips are even daisy-chainable to each other so that you create a longer strip by daisy-chaining 1 m strips together.
WS2812B LED Pixel Strip Light 5050 RGB 144
WS2812B chip based LED with the chip logic built into the LED itself (no external IC). Create magic with this magic strip having 144 LEDs in 1 meter length.
P10 Led Module Pink
|Working Voltage||220 to 440 V|
|Operating Temperature||10 to 60 Degree Celsius|
WS2812B LED Pixel Strip Light 5050 RGB 60
This is WS2812B Addressable LED Strip DC 5V (Non-Waterproof) 60 LEDs/m. The installation surface must be smooth, clean, and dry. The part of LED components cannot be fixed on the surface of the sharp edges. The strip should not be collided or crushed. The strip can be cut following the cutting lines 24-bit colour control (8-bit PWM per channel); 16.8 million colours per pixel. The one-wire digital control interface with each RGB LED draws approximately 50 mA at 5 V with red, green, and blue at full brightness.
Huidu HD-F2 Controller Card
HD-WF2（abbr. WF2）equipped with 2 lines HUB75E Port. It is a full color series of control card. It supports Wi-Fi and U disk to update programs. It is suitable for door led screens, store signboard screens, Vehicle-mounted screen and other occasions. Application software: HD2020 and LedArt (APP).The software interface is simple, the operation is convenient, and the rich display mode has the characteristics of low cost and high performance. It supports all types of full color LED panels such as P2.3, P3, P4, P6, P8, P10 etc.
There are no reviews yet.