Huidu HD-F1 Controller Card
HD-WF1（abbr WF1）equipped with 1HUB75E Port. It is a full color series of control card. It supports Wi-Fi and U disk to update programs. It is suitable for door lintel led screens, store signboard screens, Vehicle-mounted screen and other occasions. Application software: HD2020 and LedArt (APP).The software interface is simple, the operation is convenient, and the rich display mode has the characteristics of low cost and high cost performance, and supports various full-color led modules.
Huidu HD-F2 Controller Card
HD-WF2（abbr. WF2）equipped with 2 lines HUB75E Port. It is a full color series of control card. It supports Wi-Fi and U disk to update programs. It is suitable for door led screens, store signboard screens, Vehicle-mounted screen and other occasions.
Application software: HD2020 and LedArt (APP).The software interface is simple, the operation is convenient, and the rich display mode has the characteristics of low cost and high performance. It supports all types of full color LED panels such as P2.3, P3, P4, P6, P8, P10 etc.
Huidu HD-W00 Controller Card
P10 LED Module
P10 Led Module Pink
P10 Led Module Red
Aimed at the prosperous growth in this domain, we are instrumental in offering an excellent quality range of P10 LED Light Display Module.
Product Specification
| Color | RED |
| Power | 5V DC |
| Voltage | 5V |
| Type | Outdoor Type |
| Size | 320mmx160mm |
| Module Size | 320 x 160 mm |
| Light source | Electricity |
| Lightning type | LED |
| Frequency | 50-60 Hz |
WS2811 LED Pixel Strip Light 5050 RGB 30
WS2811 60 LEDs/m RGB Addressable LED Pixel Strip Light 12V DC Programmable
The WS2811 is a three-output channel LED driver circuit. Internally, it has a signal reshaping amplification driving circuit and an intelligent digital port data latch. A precise internal oscillator is also included, as well as a 12V voltage configurable constant current output drive. For the purpose of reducing power supply ripple, the 3 output channels are designed to delay turn-on function. A single NZR communication mode is used by the IC. Following the chip's power-on reset, the DIN port receives data from the controller, the first IC collects the initial 24bit data and sends it to the internal data latch, while the other data is reshaped by the internal signal reshaping amplification circuit and sent to the next cascade IC via the DO port. The signal is reduced by 24 bits after transmission for each chip. The chip cascade number is not limited by signal transmission because of auto reshaping transmit technology; it only depends on the signal transmission speed. The data latch of the IC produces various duty ratio signals at the OUTR, OUTG, and OUTB ports depending on the received 24bit data. When the DIN port inputs a reset signal, all chips synchronously send the incoming data to each segment. It will be updated with fresh information. Following the completion of the reset signal. The control signals of the OUTR, OUTG and OUTB ports were unaltered before a fresh reset signal was received. After receiving a low voltage reset signal, the IC supplied PWM data to the OUTR, OUTG, and OUTB ports, and the time retained was above 50us.
WS2811 LED Pixel Strip Light 5050 RGB 60
- ADDRESSABLE: One WS2811 IC controls three LEDs, easy to program when you use a programmable controller such as T-1000S, SP103E or SP105E
- FULL COLORFUL: 256 brightness display and full 24-bit color display. You can control each LED Pixel(3Led per pixel) and set it to any color or animation you want.
- CUTTABLE&CONNECTABLE: The LED Strip light Pixel can be cut off per 3 led cell without damaging the rest pixels. Each LED strip comes with 3pin JST-SM connectors and can be connected end to end, So you can DIY for length you want
- HOW TO GET IT WORK: 12V power supply and controller ( not included) is required, strip12V+ /DATA/GND connected correctly then it works
- WIDELY USED: Widely used on LOGO screen, advertising board, outdoor advertising signs and applied to hotel, KTV, bars, commercial street atmosphere lighting. Good for replace the traditional signs.
WS2812B LED Pixel Strip Light 5050 RGB 144
WS2812B LED Pixel Strip Light 5050 RGB 30
This is the waterproof version of addressable RGB LED strips based on the new WS2812B LEDs which have built-in LED drivers and addressing
Each LED on this strip is individually addressable, which means that you can set a different colour for each of the 30 LEDs in a 1 meter strip. All you need is one pin on your microcontroller/Arduino/Teensy etc. to control an entire strip of LEDs. These strips are even daisy-chainable to each other so that you create a longer strip by daisy-chaining 1 m strips together.
WS2812B LED Pixel Strip Light 5050 RGB 60
This is WS2812B Addressable LED Strip DC 5V (Non-Waterproof) 60 LEDs/m. The installation surface must be smooth, clean, and dry. The part of LED components cannot be fixed on the surface of the sharp edges. The strip should not be collided or crushed. The strip can be cut following the cutting lines 24-bit colour control (8-bit PWM per channel); 16.8 million colours per pixel. The one-wire digital control interface with each RGB LED draws approximately 50 mA at 5 V with red, green, and blue at full brightness.